Field Comparison of Vibration Before and After Structural Support Retrofit in a Variable-Speed Vertical Industrial Agitator

ARIS PUJA WIDIKDA, WIDODO WIDODO, NUGRAHADI DJAZAUL MUKHSININ

Abstract


Excessive vibration in vertically mounted industrial agitators can accelerate degradation of bearings, shafts, gearboxes, and supporting structures. This retrospective industrial study compares vibration measurements obtained before and after a structural support retrofit on a variable-speed vertical agitator used in a cement grinding-aid process. The two campaigns were conducted on different dates and with different vibration analysers; therefore, the observed differences are not interpreted as an isolated causal retrofit effect. At measurement point 1, horizontal vibration increased from 1.6 mm/s at 82 rpm to 13.0 mm/s at 203 rpm before the retrofit, whereas the post-retrofit campaign recorded 2.5 mm/s at 200 rpm, an observed before-and-after difference of 80.8%. At 50 Hz, points 2 and 3 changed from 6.2 to 1.7 mm/s and from 6.3 to 1.5 mm/s, respectively. Post-retrofit spectra and thermography are presented only as condition indicators; the largest reported looseness-related component was 0.84 m/s², and full-load motor temperature reached 66.3-67.7°C. The field evidence is associated with lower vibration levels following the support modification, while the dataset limitations preclude confirmation of resonance shifts or a uniquely causal mechanism.

Full Text:

PDF

References


M. Tiboni, C. Remino, R. Bussola, and C. Amici, “A review on vibration-based condition monitoring of rotating machinery,” Applied Sciences, vol. 12, no. 3, Art. no. 972, 2022, doi: 10.3390/app12030972.

M. H. Mohd Ghazali and W. Rahiman, “Vibration analysis for machine monitoring and diagnosis: A systematic review,” Shock and Vibration, vol. 2021, Art. no. 9469318, 2021, doi: 10.1155/2021/9469318.

P. Gangsar and R. Tiwari, “Signal based condition monitoring techniques for fault detection and diagnosis of induction motors: A state-of-the-art review,” Mechanical Systems and Signal Processing, vol. 144, Art. no. 106908, 2020, doi: 10.1016/j.ymssp.2020.106908.

J. Chen, C. Lin, D. Peng, and H. Ge, “Fault diagnosis of rotating machinery: A review and bibliometric analysis,” IEEE Access, vol. 8, pp. 224985-225003, 2020, doi: 10.1109/ACCESS.2020.3043743.

A. K. Devaraj and R. Adhikari, “Vibration analysis of the base structure supporting a centrifuge-motor assembly in a petroleum oil refinery,” Journal of The Institution of Engineers (India): Series C, vol. 104, pp. 393-401, 2023, doi: 10.1007/s40032-023-00919-y.

S. Laine, S. Haikonen, T. Tiainen, and R. Viitala, “Rotor resonance avoidance by continuous adjustment of support stiffness,” International Journal of Mechanical Sciences, vol. 270, Art. no. 109092, 2024, doi: 10.1016/j.ijmecsci.2024.109092.

Q. Liu, C. Tang, T. Wu, and Y. Bai, “Influence of pivot support stiffness on dynamic characteristics of vertical rotor system,” Journal of Vibroengineering, vol. 25, no. 6, pp. 1040-1052, 2023, doi: 10.21595/jve.2023.23136.

L. Bibire, A.-D. Chitimus, and V. Ciubotariu, “Design of mixing device shafts based on a proposed calculation method supported by finite element method analysis,” Machines, vol. 12, no. 7, Art. no. 479, 2024, doi: 10.3390/machines12070479.

H. Zhang, K. Lu, W. Zhang, and C. Fu, “Investigation on dynamic behaviors of rotor system with looseness and nonlinear supporting,” Mechanical Systems and Signal Processing, vol. 166, Art. no. 108400, 2022, doi: 10.1016/j.ymssp.2021.108400.

J. Lin, Y. Zhao, P. Wang, Y. Wang, Q. Han, and H. Ma, “Nonlinear responses of a rotor-bearing-seal system with pedestal looseness,” Shock and Vibration, vol. 2021, Art. no. 9937700, 2021, doi: 10.1155/2021/9937700.

M. Jiang, J. Wu, X. Peng, and X. Li, “Nonlinearity measure based assessment method for pedestal looseness of bearing-rotor systems,” Journal of Sound and Vibration, vol. 411, pp. 232-246, 2017, doi: 10.1016/j.jsv.2017.09.002.

Z. Qin, Q. Han, and F. Chu, “Bolt loosening at rotating joint interface and its influence on rotor dynamics,” Engineering Failure Analysis, vol. 59, pp. 456-466, 2016, doi: 10.1016/j.engfailanal.2015.11.002.

S. Wei, W. Lu, and F. Chu, “Speed characteristics of disk-shaft system with rotating part looseness,” Journal of Sound and Vibration, vol. 469, Art. no. 115127, 2020, doi: 10.1016/j.jsv.2019.115127.

P. Zhou, S. Chen, Q. He, D. Wang, and Z. Peng, “Rotating machinery fault-induced vibration signal modulation effects: A review with mechanisms, extraction methods and applications for diagnosis,” Mechanical Systems and Signal Processing, vol. 200, Art. no. 110489, 2023, doi: 10.1016/j.ymssp.2023.110489.

R. Wang, X. Zhan, H. Bai, E. Dong, Z. Cheng, and X. Jia, “A review of fault diagnosis methods for rotating machinery using infrared thermography,” Micromachines, vol. 13, no. 10, Art. no. 1644, 2022, doi: 10.3390/mi13101644.

C. Mongia, D. Goyal, and S. Sehgal, “Vibration response-based condition monitoring and fault diagnosis of rotary machinery,” Materials Today: Proceedings, vol. 50, pt. 5, pp. 679-683, 2022, doi: 10.1016/j.matpr.2021.04.395.

Y. Yang, H. Ouyang, Y. Yang, D. Cao, and K. Wang, “Vibration analysis of a dual-rotor-bearing-double casing system with pedestal looseness and multi-stage turbine blade-casing rub,” Mechanical Systems and Signal Processing, vol. 143, Art. no. 106845, 2020, doi: 10.1016/j.ymssp.2020.106845.

Y. Yang, G. Chen, H. Ouyang, Y. Yang, and D. Cao, “Nonlinear vibration mitigation of a rotor-casing system subjected to imbalance-looseness-rub coupled fault,” International Journal of Non-Linear Mechanics, vol. 122, Art. no. 103467, 2020, doi: 10.1016/j.ijnonlinmec.2020.103467.

Y. Liu, Y. Zhao, J. Li, H. Lu, and H. Ma, “Feature extraction method based on NOFRFs and its application in faulty rotor system with slight misalignment,” Nonlinear Dynamics, vol. 99, pp. 1763-1777, 2020, doi: 10.1007/s11071-019-05340-8.

W. Zhao, C. Yue, and W. Shen, “Finite element simulation and structure optimization of the agitating mechanism of double shaft vibrating mixer,” Journal of Mechanical Strength, vol. 42, no. 6, pp. 1496-1502, 2020, doi: 10.16579/j.issn.1001.9669.2020.06.032.

SPM Instrument AB, “Leonova Infinity – Vibration ISO 2372,” Technical Data TD-225 B, Strängnäs, Sweden. [Online]. Available: https://extranet.spminstrument.se/Documents/Downloads/Support/TD-Sheets/LEOInB.pdf. [Accessed: 21-Oct-2026].

PRUFTECHNIK, “VIBXPERT II Technical Data,” Fluke Deutschland GmbH, Ismaning, Germany. [Online]. Available: https://www.pruftechnik.com/fileadmin/Products-Services/Products/Condition-Monitoring-Systems/Vibration-Analysis-and-Balancing/VIBXPERT-II/Downloads/6013867b_en_fds_3419_vibxpert_ii_ds.pdf. [Accessed: 21-Oct-2026].

International Organization for Standardization, ISO 20816-3:2022, Mechanical vibration — Measurement and evaluation of machine vibration — Part 3: Industrial machinery with a power rating above 15 kW and operating speeds between 120 r/min and 30 000 r/min. Geneva, Switzerland: ISO, 2022.




DOI: https://doi.org/10.31284/j.jmesi.2026.v6i2.9527

Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

Published by:
Institut Teknologi Adhi Tama Surabaya, Indonesia

Editorial Address
Journal of Mechanical Engineering, Science, and Innovation is licensed under CC BY-NC 4.0