Analysis of Tube Expansion Percentage on Microstructure and Hardness of 316L Stainless Steel Tube-to-Tubesheet Connections with GTAW Process

Moh. Syaiful Amri, Bachtiar Bachtiar, Moh. Miftachul Munir, Mukhlis Mukhlis, Muhammad Ari, Ilham Kurniawan

Abstract


This study analyzes the effect of varying tube expansion percentages on the mechanical properties, microstructure, and hardness of SA-213 TP316L tubes joined to SA-240 TP316L tubesheets in a shell-and-tube type heat exchanger. The tube expansion process was carried out using a roller expander with three expansion levels: 4%, 8%, and 12%, followed by Gas Tungsten Arc Welding (GTAW) at 150 A. Microstructural observations revealed that all joint zones were dominated by austenite with small amounts of delta ferrite, where increasing expansion percentages induced significant changes in the expand area: slight deformation at 4%, grain elongation at 8%, and pronounced grain distortion at 12%. Macrostructural observations showed perfect fusion between the tube and tubesheet for all variations, with no macro defects such as lack of fusion or porosity. Vickers hardness testing indicated the highest values in the expand area for all variations, with a maximum of 377 Kgf/mm², exceeding the standard limit of 250 Kgf/mm² for stainless steel. The hardness of the base metal was around 180 Kgf/mm², while the weld metal ranged from 220–230 Kgf/mm² due to delta ferrite formation. The increase in hardness in the expand area was attributed to cold working effects, indicating that post-tube expansion heat treatment is necessary to reduce residual stresses and restore the optimal mechanical properties of the material.

Full Text:

PDF

References


A. Al-Odhaib and A. S. Alaboodi, “Review on Heat Exchanger Tube-To-Tubesheet Joining,” Int. J. Adv. Res. Eng. Technol. (IJARET), vol. 11, no. 10, pp. 1395–1405, 2020, doi: 10.34218/IJARET.11.10.2020.133.

J. Hernández-Ortega, J. J. Jiménez-Ballesta, and A. E. Pedreño, “Analysis of Tube-to-Tubesheet Welding in Carbon Steel Heat Exchangers of a Double Plate Header Box,” pp. 1–17, 2022.

D. T. Thekkuden, A. H. I. Mourad, et al., “Combined Effect of Tungsten Inert Gas Welding and Roller Expansion Processes on Mechanical and Metallurgical Characteristics of Heat Exchanger Tube-To-Tubesheet Joints,” J. Mater. Res. Technol., vol. 21, pp. 4724–4744, 2022, doi: 10.1016/j.jmrt.2022.11.043.

D. T. Thekkuden, A. H. I. Mourad, et al., “Investigation of Expansion Percentages and Groove Inclusions on the Performance of Welded, Expanded, Welded-Expanded Tube-to-Tubesheet Joints,” J. Mater. Res. Technol., vol. 22, pp. 2078–2092, 2023, doi: 10.1016/j.jmrt.2022.12.045.

TEMA, Standards of the Tubular Exchanger Manufacturers Association, 8th ed., 11th Printing. Tarrytown, NY, USA: TEMA, 2023.

Z. Yan, X. Zou, S. Li, et al., “A Study on the Thermo-Mechanical History, Residual Stress, and Dynamic Recrystallization Mechanisms in Additively Manufactured Austenitic Stainless Steels,” Metals, vol. 12, no. 7, 2022, doi: 10.3390/met12071109.

I. Z. Awan and A. Q. Khan, “Recovery, Recrystallization, and Grain-Growth,” J. Chem. Soc. Pakistan, vol. 41, no. 1, pp. 1–42, 2019, doi: 10.52568/000707/jcsp/41.01.2019.

W. Ji, L. Xu, S. Dai, et al., “Effect of Process Parameters on Hardness and Microstructure of 316L Stainless Steel Manufactured by Selective Laser Melting,” Cailiao Daobao/Materials Reports, vol. 35, no. 22, pp. 22125–22131, 2021, doi: 10.11896/cldb.20070232.

Hasrin, Herizal, and Hanif, “Analisa Pengaruh Proses GTAW dan SMAW terhadap Ketangguhan Sambungan Pengelasan Material AISI 1050,” J. Teknol., vol. 2, no. 1, pp. 19–25, 2020.

J. C. Lippold, D. J. Kotecki, and A. J. Wiley, Weldability of Stainless Steels. Hoboken, NJ, USA: Wiley, 2005.

ASME, Section II, Part A: Ferrous Material Specifications (SA-451 to End), ASME Boiler and Pressure Vessel Code, 2023.

W. D. Callister and D. G. Rethwisch, Materials Science and Engineering: An Introduction, 10th ed. Hoboken, NJ, USA: Wiley, 2018.

S. Kou, Welding Metallurgy, 2nd ed. Hoboken, NJ, USA: Wiley-Interscience, 2003.

ASME, Section IX: Welding and Brazing Qualifications, ASME Boiler and Pressure Vessel Code, 2022.

N. Haneklaus, R. Reuven, C. Cionea, et al., “Tube Expansion and Diffusion Bonding of 316L Stainless Steel Tube-to-Tube Sheet Joints Using a Commercial Roller Tube Expander,” J. Mater. Process. Technol., vol. 234, pp. 27–32, 2016, doi: 10.1016/j.jmatprotec.2016.03.008.

C. Zhang, D. J. Jensen, et al., Microstructure and Texture Evolution During Cold Rolling of 316L Stainless Steel, vol. 52, 2021.

K. Touileb, A. C. H. Hedhibi, et al., “Mechanical, Microstructure, and Corrosion Characterization of Dissimilar Austenitic 316L and Duplex 2205 Stainless-Steel ATIG Welded Joints,” Materials, vol. 15, no. 7, 2022, doi: 10.3390/ma15072470.

P. Noga, T. Skrzekut, M. Wędrychowicz, et al., “The Influence of Various Welding Methods on the Microstructure and Mechanical Properties of 316Ti Steel,” Materials, vol. 17, no. 7, 2024, doi: 10.3390/ma17071681.

X. Ren, W. Yang, et al., “Effect of Expansion Deformation on the Mechanical Properties and Corrosion Resistance of an AISI 304 Stainless Steel Tube in Water from an Oilfield,” Coatings, vol. 12, no. 10, 2022, doi: 10.3390/coatings12101415.

S. Wang, H. Xue, Y. Cui, et al., “Effect of Different Cold Working Plastic Hardening on Mechanical Properties of 316L Austenitic Stainless Steel,” Procedia Struct. Integr., vol. 13, pp. 1940–1946, 2018, doi: 10.1016/j.prostr.2018.12.267.

M. Odnobokova, Z. Yanushkevich, et al., “On the Strength of a 316L-Type Stainless Steel Subjected to Cold or Warm Rolling Followed by Annealing,” Materials, vol. 13, no. 9, 2020, doi: 10.3390/ma13092116.

Heat Exchanger Design Handbook, 2nd ed., vol. 2, “Shell and Tube Heat Exchanger Design,” 2013.




DOI: https://doi.org/10.31284/j.jmesi.2025.v5i2.8161

Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

Published by:
Mechanical Engineering Department - Institut Teknologi Adhi Tama Surabaya

Editorial Address
Journal of Mechanical Engineering, Science, and Innovation is licensed under CC BY-NC 4.0