Geotextile-Reinforced Haul Roads for Improved Hauling Speed in Open-Pit Coal Mining

Mila Kusuma Wardani, Maula Amalia Az-Zahro

Abstract


Haul road rehabilitation should be assessed through both the distribution of road support and the transport components that constrain productivity. This study examined an approximately 1 km section of Jalan Mukmin at Gurimbang Mine Operation, PT Berau Coal, Indonesia, following combined nonwoven geotextile placement, aggregate addition, and compaction. A descriptive before-and-after comparison used penetration-derived California bearing ratio (CBR) estimates at ten stations and reported Komatsu HD785 speeds and cycle-time components. Station dispersion, a diagnostic exclusion of the highest post-rehabilitation estimate, and cycle-time sensitivity were evaluated. Mean CBR increased from 21.58% to 60.01%, while its coefficient of variation increased from 19.33% to 57.97%. Nine stations improved, but one decreased. Excluding the highest station for sensitivity analysis retained a mean increase from 21.92% to 51.78%, indicating that the direction of change was not dependent on that station alone. Cycle time decreased from 22.06 to 16.62 min; loaded travel accounted for 65.63% of the reduction. Under fixed volume and efficiency assumptions, calculated productivity increased from 115.46 to 153.25 bank cubic metres per hour. An illustrative additional 1 min of cycle delay reduced the post-rehabilitation estimate to 144.56. The contribution is a transparent joint assessment showing why a higher mean road-support estimate does not establish spatial uniformity, and why operational gains depend on preserving travel-time savings. Uncontrolled conditions and discrepancies between penetration logs and summary values limit causal attribution and the geotechnical magnitudes. The results support targeted station verification and component-based transport monitoring, rather than certification of long-term road stability or an isolated geotextile effect.

Keywords


Mine haul road; Nonwoven geotextile; California bearing ratio; Spatial variability; Truck cycle time

Full Text:

PDF

References


J. Gouda, D. S. Rami Reddy, V. Srinivasan, V. Butle, “Comprehensive Review of Haul Road Design Methods: a Comparative Approach,” Arch. Min. Sci., vol. 69, no. 3, pp. 529–554, 2024, doi: 10.24425/ams.2024.151449.

S. Ercins, M. Bostancıoğlu, “Investigation of the sufficiency of CBR method sections used in the design of mine haul roads with the mechanistic method,” Rev. Constr., vol. 24, no. 1, pp. 75–88, 2025, doi: 10.7764/rdlc.24.1.75.

D. Alegre, R. de Lemos Peroni, E. da Rosa Aquino, F. Dille, “A method to assess haul roads rolling resistance using dispatch system data,” Mining Technology, pp. 1–12, 2021, doi: 10.1080/25726668.2021.1935098.

G. R. d. S. Maior, R. d. L. Peroni, J. L. V. Mariz, “Assessing the impact of road geometry and rolling resistance on transportation costs and productivity in an iron ore mine in Brazil,” REM Int. Eng. J., vol. 78, no. 4, Art. no. e250002, 2025, doi: 10.1590/0370-44672025780002.

P. Silva, H. Lima, V. Torres, L. Silveira, F. Souza, “Evaluation of road roughness and its influence on operating parameters in open-pit mines,” Concilium, vol. 24, no. 17, pp. 654–670, 2024, doi: 10.53660/clm-3947-24r52.

M. Singh, A. Trivedi, S. K. Shukla, “Influence of Geosynthetic Reinforcement on Unpaved Roads Based on CBR, and Static and Dynamic Cone Penetration Tests,” Int. J. Geosynth. Ground Eng., vol. 6, no. 2, Art. no. 13, 2020, doi: 10.1007/s40891-020-00196-0.

M. Singh, A. Trivedi, S. K. Shukla, “Unpaved test sections reinforced with geotextile and geogrid,” Mater. Today Proc., vol. 32, pp. 706–711, 2020, doi: 10.1016/j.matpr.2020.03.260.

M. Singh, A. Trivedi, S. K. Shukla, “Evaluation of geosynthetic reinforcement in unpaved road using moving wheel load test,” Geotext. Geomembr., vol. 50, no. 4, pp. 581–589, 2022, doi: 10.1016/j.geotexmem.2022.02.005.

E. V. Cuelho, S. W. Perkins, “Geosynthetic subgrade stabilization – Field testing and design method calibration,” Transp. Geotech., vol. 10, pp. 22–34, 2017, doi: 10.1016/j.trgeo.2016.10.002.

N. J. Sarma, A. Dey, “Improvement of Long-Term Performance of Unpaved Road Constructed Over Marginalized Subsoil Using Geotextile Reinforcement,” Int. J. Geosynth. Ground Eng., vol. 10, no. 3, Art. no. 39, 2024, doi: 10.1007/s40891-024-00550-6.

C. H. Ho, J. DeGeyter, D. Zhang, “Five-Year Performance Evaluation of Geogrid Reinforcement in Low-Volume Unpaved Roads Using Dynamic Cone Penetrometer, Plate Load Test and Roadway Sensing,” Geotechnics, vol. 3, no. 2, pp. 306–319, 2023, doi: 10.3390/geotechnics3020018.

M. Asof, D. Purbasari, M. A. Agustian Putra, “Perbaikan Jalan Angkut Menggunakan Geotextile untuk Meningkatkan Produktivitas HD 785 pada Site Gurimbang Mine Operation, PT. Berau Coal,” Cantilever: Jurnal Penelitian dan Kajian Bidang Teknik Sipil, vol. 12, no. 1, pp. 19–28, 2023, doi: 10.35139/cantilever.v12i1.213.

C. P. Sagar, M. Badiger, K. H. Mamatha, S. V. Dinesh, “Prediction of CBR using dynamic cone penetrometer index,” Mater. Today Proc., vol. 60, pp. 223–228, 2022, doi: 10.1016/j.matpr.2021.12.467.

M. Dafalla, A. Shaker, M. Al-Shamrani, “Use of the Dynamic Cone Penetrometer in Compacted Clay–Sand Layers,” Appl. Sci., vol. 12, no. 22, Art. no. 11547, 2022, doi: 10.3390/app122211547.

W. T. Hong, J. D. Yu, S. Y. Kim, J. S. Lee, “Dynamic Cone Penetrometer Incorporated with Time Domain Reflectometry (TDR) Sensors for the Evaluation of Water Contents in Sandy Soils,” Sensors, vol. 19, no. 18, Art. no. 3841, 2019, doi: 10.3390/s19183841.

Direktorat Jenderal Bina Marga, Pedoman Cara Uji CBR dengan Dynamic Cone Penetrometer (DCP), Surat Edaran Menteri Pekerjaan Umum No. 04/SE/M/2010. Jakarta, Indonesia: Kementerian Pekerjaan Umum, 2010.

Departemen Pekerjaan Umum, Petunjuk Perencanaan Tebal Perkerasan Lentur Jalan Raya dengan Metode Analisa Komponen. Jakarta, Indonesia, 1987.

M. Singh, A. Trivedi, S. K. Shukla, “Strength enhancement of the subgrade soil of unpaved road with geosynthetic reinforcement layers,” Transp. Geotech., vol. 19, pp. 54–60, 2019, doi: 10.1016/j.trgeo.2019.01.007.

A. Hasheminezhad, H. Ceylan, S. Kim, E. Tutumluer, “Evaluation of 3D-printed model geogrids and composite geosynthetics made from recycled plastics: Bridging laboratory insights with field performance,” Constr. Build. Mater., vol. 465, Art. no. 140258, 2025, doi: 10.1016/j.conbuildmat.2025.140258.

A. Hasheminezhad, H. Ceylan, S. Kim, E. Tutumluer, “Performance Evaluation of Unpaved Roads Stabilized with Composite Geosynthetic Made of Recycled Plastic Geogrid and Nonwoven Geotextile,” Geotechnical Frontiers 2025 Foundations Retaining Structures and Geosynthetics, vol. GSP 364, pp. 354–364, 2025, doi: 10.1061/9780784485972.035.




DOI: https://doi.org/10.31284/j.jemt.2025.v5i2.9677

Refbacks

  • There are currently no refbacks.


Copyright (c) 2026 Mila Kusuma Wardani, Maula Amalia Az-Zahro

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

Published by Lembaga Penelitian dan Pengabdian Masyarakat (LPPM)
Institut Teknologi Adhi Tama Surabaya (ITATS)