Work Posture Analysis Based on Posture Evaluation Index Case Study of PT XTZ Workshop Department

Ardand Putra Pratama, Mochamad Sulaiman, Abdul Alimul Karim

Abstract

Manual handling in workshop activities has the potential to cause greater injury to workers than moving goods with the help of tools. Therefore, this study conducted an analysis of the risk of occupational diseases using the PEI method in the workshop department with the aim of evaluating the work posture of workers in Manual Material Handling activities. The simulation with Technomatic Jack 8.4 software that has been run shows the calculation of the PEI value based on the LBA, OWAS, and RULA values in 10 manual handling movements. It was found that there were two movements that had a PEI value of more than 2 (Middle - Low Injury) which means it is dangerous if it continues to be done, both movements include movements when lifting the breakdrum and when moving the breakdrum, the LBA obtained has a value exceeding the NIOSH standard of 3400 N, in the same movement the OWAS produced is worth 4 and 3, and RULA in the same movement has a value of 7. So that in the movements when lifting the breakdrum and when moving the breakdrum, work improvements are needed to avoid injury.

Full Text:

PDF

References

I. R. Muttaqin and N. R. Radliya, “Sistem Informasi Pelayanan Notebook,” 2018.

A. Asy’Ari, “ANALISIS KETERLAMBATAN SUPPLY SPARE PART YANG MENGGANGGU MANAJEMEN PERAWATAN KAPAL MT. ENDURO DI PT. PERTAMINA PERKAPALAN JAKARTA,” vol. 53, no. 9, pp. 1689–1699, 2019.

A. Anwardi and C. Mulyadi, “Merancang Ulang Manual Material Handling Troli Kursi Ergonomis Untuk Mengurangi Tingkat Keluhan Rasa Sakit dan Meningkatkan Produktivitas Kerja Karyawan Banquet, vol. 5, no. 1, p. 11, 2020.

P. Anggraika, A. Apriany, and D. Pujiana, “HUBUNGAN POSISI DUDUK DENGAN KEJADIAN LOW BACK PAIN ( LBP ) PENDAHULUAN Salah satu nyeri yang paling sering terjadi di dunia adalah nyeri punggung bawah ( NPB ).vol. 4, pp. 1–10, 2019.

M. R. Firdaus and N. R. As’ad, “Perancangan Fasilitas Kerja Metode PEI Menggunakan Virtual Environment Modelling,” J. Ris. Tek. Ind., pp. 171–178, 2022.

N. F. Dewi, “IDENTIFIKASI RISIKO ERGONOMI DENGAN METODE NORDIC BODY Jurnal Sosial Humaniora Terapan,” osial Hum. Terap., vol. 2, no. 2, pp. 125–134, 2020.

A. Atoillah, “Analisis Stasiun Kerja Pemotongan Tahu Dan Rancang Bangun Alat Potong Tahu Dengan Virtual Environment Pada Industri Kecil Tahu,” 2019.

D. Setiawan, Z. Fatimah Hunusalela, and R. Nurhidayati, “Usulan Perbaikan Sistem Kerja Di Area Gudang Menggunakan Metode Rula Dan Owas PT Wijaya Karya (Persero) Tbk,” JATI UNIK J. Ilm. Tek. dan Manaj. Ind., vol. 4, no. 2, pp. 78–90, 2021.

J. Eka, S. Casym, and D. N. Oktiara, “Analisis Postur Tubuh Pekerja Home Industry Pastel Menggunakan Analisis Rapid Upper Limb Assesment ( RULA ),” pp. 631–635, 2020.

P. Oktaviani, R. Regiana, D. Satya, and A. Herliawan, “Analisis Postur Tubuh Pekerja di PT PO dengan Menggunakan Metode Posture Evaluation Index (PEI),” pp. 232–239, 2022.

Refbacks

  • There are currently no refbacks.