Pengaruh Variasi Massa Raw Material dan Jenis Material Terhadap Respon Steady State Error Spindle Mesin Lathe Mini

Muhammad Ali Masykur, Ahmad Anas Arifin, Desmas Arifianto Patriawan

Abstract

Lathe machines have played an important role in the development of the world of education and industry, learning how to operate lathe machines also requires expertise in accuracy, accuracy, speed, and improving quality and producing maximum results, this research method focuses on the analysis of motor spindle rpm and motor response mini lathe machine when given variations in load, material and feed, namely variations in spindle speed of 1000, 2000 and 3000 Rpm, mass of raw material Teflon PL and Aluminum 50, 100 and 150 grams, feeding 0.5 mm. The results of the study were to The greatest steady state error averagely was to 8 volt by 2000 rpm; it situation was obtained at no feeding procedure at a voltage of 8 volts with a target of 2000 rpm, without feeding conditions. Further, the feeding depth 0.5mm was obtained the greatest steady state error at 4 volt and 1000 rpm.

Keywords: Lathe, Steady State Response, Spindle Speed

References

B. Kurniawan, E., Syaifurrahma., Jekky, “Rancang Bangun Mesin CNC Lathe Mini 2 Axis,” J. Engine Energi, Manufaktur, dan Mater., vol. 4, no. 2, pp. 83–90, 2020.

F. Rahmadianto, D. Wilis, and L. Basuki, “Analisa Putaran Spindle dan Kedalaman Potong Terhadap Keausan Pahat Positive dan Negative Rhombic Insert,” vol. 8, no. September, pp. 34–38, 2017.

S. Pendidikan et al., “Pengaruh Variasi Kedalaman Pemakanan Dan Kecepatan Putar Spindle Terhadap Tingkat Kekasaran Permukaan Aluminium 6061 Pada Mesin Cnc Tu- 2a Dengan Program Absolut G01 Pebri Dwi Kurniawan Mochamad Arif Irfa ’ I,” vol. 03, no. 2, pp. 120–125, 2014.

D. Seprianto, “Pengaruh Spindle Speed , Feeding Dan Depth Of Cut Pada Turning Cnc Dengan Material Plastik Terhadap Kekasaran Permukaan,” vol. 6, no. April, pp. 41–47, 2014.

W. WALUYO, A. FITRIANSYAH, and S. SYAHRIAL, “Analisis Penalaan Kontrol PID pada Simulasi Kendali Kecepatan Putaran Motor DC Berbeban menggunakan Metode Heuristik,” ELKOMIKA J. Tek. Energi Elektr. Tek. Telekomun. Tek. Elektron., vol. 1, no. 2, p. 79, 2013, doi: 10.26760/elkomika.v1i2.79.

R. Poeng, F. A. Rauf, J. Teknik, M. Fakultas, T. Universitas, and S. Ratulangi, “Analisis Pengaruh Putaran Spindle Terhadap Gaya Potong Pada Mesin Bubut,” J. Tekno Mesin, vol. 2, no. 2, pp. 6–11, 2015.

A. Priyatmojo, J. T. Mesin, U. N. Semarang, and U. N. Semarang, “Pengaruh Kecepatan Spindle Dan Kedalaman Pemakanan Proses Cnc Frais Terhadap Kekasaran Dan Kekerasan Permukaan Remelting Blok Silinder,” J. Kompetensi Tek., vol. 11, no. 1, pp. 25–29, 2019, doi: 10.15294/jkomtek.v11i1.19072.

I. Malik, Azharuddin, and S. Riyadi, “Pengaruh Spindle Speed, Feed Rate, Dan Depth of Cut Terhadap Akurasi Hasil Permesinan Pada Mesin Cnc Router 3 Sumbu,” Mech. Eng. Dep. Politek. Negeri Sriwijay, vol. 11 no. 2, no. 2, pp. 33–40, 2019.

T. Hidayat, T. Widagdo, D. Seprianto, and M. Yunus, “Feeding Pada Proses Surface Milling Menggunakan Mesin,” J. Austenit, vol. 8, no. 1, pp. 13–16, 2016.

P. Kecepatan, P. Spindle, R. P. M. Dan, and B. Ems, “Pengaruh Kecepatan Putar Spindle (Rpm) Dan Jenis Sudut Pahat Pada Proses Pembubutan Terhadap Tingkat Kekasaran Benda Kerja Baja Ems 45,” Sainteknol J. Sains dan Teknol., vol. 15, no. 1, pp. 85–94, 2017, doi: 10.15294/sainteknol.v15i1.9881.

D. A. Patriawan, M. Ulum, M. S. Alqoroni, and A. Y. Ismail, “Transient Response Performance Test on Aftermarket Motorcycle Rear Suspension in Indonesia,” J. Mech. Eng. Sci. Innov., vol. 1, no. 2, pp. 69–76, 2021, doi: 10.31284/j.jmesi.2021.v1i2.2297.

A. Mashudi and N. A. Susanti, “Pengaruh Media Pendingin dan Kecepatan Putar Spindle Terhadap Hasil Kekasaran Permukaan Benda Kerja Pada Proses Finishing Menggunakan Mesin Bubut CNC PU,” J. Pendidik. Tek. Mesin, vol. 9, no. 3, pp. 57–66, 2020.

D. A. Patriawan, B. P. Natakusuma, A. A. Arifin, H. S. Maulana, H. Irawan, and B. Setyono, “Uji Presisi dari Nonholonomic Mobile Robot pada Rancang Bangun Sistem Navigasi,” J. Mech. Eng. Sci. Innov., vol. 1, no. 1, pp. 28–37, 2021, doi: 10.31284/j.jmesi.2021.v1i1.1760.

Ninla Elmawati Falabiba, “Pengaruh Kecepatan Spindle Dan Kedalaman Pemakanan Terhadap Kekasaran Permukaan Pemesinan Bubut CNC Baja ST41,” vol. 2, no. 7, 2019.

Refbacks

  • There are currently no refbacks.