Behaviour of Rectangular Concrete Filled Tubes and Circular Concrete Filled Tubes under Axial Load

Cintantya Budi Casita, I Putu Ellsa Sarassantika, Roro Sulaksitaningrum

Abstract


This paper presents the result behavior of two different type of Concrete Filled Tubes: Rectangular Concrete Filled Tubes (RCFT) and Circular Concrete Filled Tubes (CCFT). In this model, the column end is fixed and the axial load, Paxial, are applied to the column end. The amount of axial load is divided into 5 steps, which increasing continuously. The dimension of the column is 300x300x10 for RCFT and 300x10 for CCFT. As the results, stress distribution, load-deformation curve, load-stress curve, and weight calculation are compared. And it shows that the CCFT gives better performance than the RCFT.


Full Text:

PDF

References


Morino, S., Fujimoto, T., Nishiyama, I., Noguchi, T. Baba, T. and Sakino, K., “Eccentric Compression Test of Concrete Filled Square Tubular Stub Column using High Strength Material,” J. Struct. Constr. Eng., pp. 173–180, 1997.

S. Morino, I. Researcher, and K. Tsuda, “Design and Construction of Concrete Filled Steel Tube Column System in Japan,” J. Earthq. Eng. Eng. Seismol., vol. 4, pp. 51–73, 2004.

W. Naguib and A. Mirmiran, “Creep Modelling for Concrete-Filled Steel Tubes,” J. Constr. Steel Res., vol. 59, pp. 1327–1344, 2003.

Badan Standardisasi Nasional, “Tata Cara Perencanaan Ketahanan Gempa Untuk Bangunan Gedung,” 2012.

Badan Standardisasi Nasional, “Tata Cara Perencanaan Struktur Baja Untuk Bangunan Gedung,” 2015.

Badan Standardisasi Nasional, “Tata Cara Perencanaan Struktur Beton Untuk Bangunan Gedung,” 2013.

Commission of the European Communities (CEC)., Eurocode 3: Design of steel structures. Part 1-2: General rules. Structural fire design., vol. 2, no. 2005. 1995.

T. Jankowiak and Lodygowski T., “Identification of parameters of concrete damage plasticity constitutive model,” Found. Civ. Environ. Eng., vol. 6, no. 2005, pp. 53–69, 2014.

European Committee for Standardization (CEN), Eurocode 2: Design of Concrete Structures – Part 1-1: General Rules and Rules for Buildings, vol. 1, no. 2004. 2004.

M. Pavlovic, Z. Markovi, M. Veljkovi, and D. Bu, “Bolted Shear Connectors Vs. Headed Studs Behaviour in Push-Out Tests,” J. Constr. Steel Res., vol. 88, pp. 134–149, 2013.




DOI: https://doi.org/10.31284/j.jasmet.2020.v1i1.868

Refbacks

  • There are currently no refbacks.


Copyright (c) 2020 Cintantya Budi Casita, I Putu Ellsa Sarassantika, Roro Sulaksitaningrum

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Mailing Address: Journal of Applied Sciences, Management and Engineering Technology - ITATS Institut Teknologi Adhi Tama Surabaya Jl. Arief Rahman Hakim No.100, Surabaya 60117 email: [email protected] Website : https://ejurnal.itats.ac.id/jasmet/index Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.